| 普通穴 | ﾈｼﾞｻｲｽﾞ | 穴径 |
|---|---|---|
| M3用 | 3.4 ｷﾘ | |
| M4用 | 4.5 ｷﾘ | |
| M5用 | 5.5 ｷﾘ | |
| M6用 | 6.6 ｷﾘ | |
| M8用 | 9.0 ｷﾘ | |
| M10用 | 11 ｷﾘ | |
| M12用 | 14 ｷﾘ | |
| M16用 | 18 ｷﾘ | |
| ﾊﾞｶ穴(取付寸法が甘目でも良い時) | ﾈｼﾞｻｲｽﾞ | 穴径 |
| M3用 | 4.5 ｷﾘ | |
| M4用 | 6 ｷﾘ | |
| M5用 | 7 ｷﾘ | |
| M6用 | 8 ｷﾘ | |
| M8用 | 12 ｷﾘ | |
| M10用 | 14 ｷﾘ | |
| M12用 | 16 ｷﾘ | |
| M16用 | 22 ｷﾘ | |
| ﾀｯﾌﾟの下穴 | ﾈｼﾞｻｲｽﾞ | 穴径 |
| M3用 | 2.5 ｷﾘ | |
| M4用 | 3.3 ｷﾘ | |
| M5用 | 4.2 ｷﾘ | |
| M6用 | 5.0 ｷﾘ | |
| M8用 | 6.8 ｷﾘ | |
| M10用 | 8.5 ｷﾘ | |
| M12用 | 10.3 ｷﾘ | |
| M16用 | 14 ｷﾘ |
| ｻﾞｸﾞﾘ穴(ﾜｯｼｬｰ無し) | ﾈｼﾞｻｲｽﾞ | 貫通穴径 | ｻﾞｸﾞﾘ穴径 | ｻﾞｸﾞﾘ深(ﾂﾗ) | SW有ﾌｶｻ増 |
|---|---|---|---|---|---|
| M3用 | 3.4 ｷﾘ | φ6.5 | 3.5 | +1 | |
| M4用 | 4.5 ｷﾘ | φ8 | 4.5 | +1 | |
| M5用 | 5.5 ｷﾘ | φ9.5 | 5.5 | +1.5 | |
| M6用 | 6.6 ｷﾘ | φ11 | 6.5 | +1.5 | |
| M8用 | 9 ｷﾘ | φ14 | 9 | +2 | |
| M10用 | 11 ｷﾘ | φ17.5 | 11 | +2.5 | |
| M12用 | 14 ｷﾘ | φ20 | 13 | +2.5 | |
| M16用 | 18 ｷﾘ | φ26 | 17.5 | - | |
| 皿穴 | ﾈｼﾞｻｲｽﾞ | 貫通穴径 | 皿穴頭径 | 皿穴径許容差 | 皿穴ﾌｶｻ(斜部) |
| M2用 | 2.2 ｷﾘ | φ4.4 |
+0.4 -0.1 |
1.2 | |
| M2.3用 | 2.5 ｷﾘ | φ5 | 1.3 | ||
| M2.5用 | 2.7 ｷﾘ | φ5.4 | 1.4 | ||
| M2.6用 | 2.8 ｷﾘ | φ5.6 | 1.5 | ||
| M3用 | 3.2 ｷﾘ | φ6.6 |
+0.4 -0.2 |
1.8 | |
| M4用 | 4.3 ｷﾘ | φ8.6 | 2.2 | ||
| M5用 | 5.3 ｷﾘ | φ10.6 |
+0.5 -0.2 |
2.7 | |
| M6用 | 6.4 ｷﾘ | φ12.8 | 3.3 | ||
| M8用 | 8.4 ｷﾘ | φ16.8 | 4.3 | ||
| 極低六角ﾎﾞﾙﾄ | ﾈｼﾞｻｲｽﾞ | 貫通穴径 | ｻﾞｸﾞﾘ穴径 | ｻﾞｸﾞﾘ深(ﾂﾗ) | SW有ﾌｶｻ増 |
| M3用 | ﾈｼﾞ破損多につき使用禁止 | ||||
| M4用 | 4.5 ｷﾘ | φ9 | 2 | +1 | |
| M5用 | 5.5 ｷﾘ | φ10 | 2 | +1.5 | |
| M6用 | 6.6 ｷﾘ | φ11 | 2 | +1.5 | |
| M8用 | 9 ｷﾘ | φ14 | 2 | +2 | |
| M10用 | 11 ｷﾘ | φ17.5 | 2 | +2.5 | |
| ﾈｼﾞｻｲｽﾞ | 最低ｶｶﾘ | 基本ｶｶﾘ |
| M3 | 3 | 4.5 |
| M4 | 4 | 6 |
| M5 | 5 | 7.5 |
| M6 | 6 | 9 |
| M8 | 8 | 12 |
| M10 | 10 | 15 |
| M12 | 12 | 18 |
| M16 | 16 | 24 |
